- #AEON LABS Z STICK II HOW TO#
- #AEON LABS Z STICK II SERIAL#
- #AEON LABS Z STICK II SOFTWARE#
- #AEON LABS Z STICK II PC#
- #AEON LABS Z STICK II BLUETOOTH#
These were some other tools I found from Zensys
#AEON LABS Z STICK II PC#
The Z-Wave PC controller is not a very user friendly interface but you can watch the z-wave packets now if you want or use the z-stick with a another 3rd party controller software. You will see lots of other nodes listed will be all your other devices connect. So now if you look back at the Z-Wave PC controller You will now be able to close the vera interface I name mine "Aeon Z-Stick" and set the room that I wanted. It should then detect the Z-Stick and you get to name the device in your network (Remember that you may need to be with in 3m (10fft) of the vera when trying to add a new device)ģ) Then press the Next button to move in to Inclusion mode So now we Put our Vera box in to Inclusion Mode.ġ) Login to Vera Box (Using a vera3 for this topic)Ģ) Select Devices -> Add Devices -> Other Devices -> Other ZWave device The Z-Stick is now ready to be added to existing network Its the lightning bolt icon next to the X icon
#AEON LABS Z STICK II HOW TO#
Located on the panel to the right under the Controller Tab This topic is about how to add a Aeon Labs Z-Stick as a second controller to. Z-Uno is a mix of Z-Wave home automation radio protocol power and Arduino simplicity. Should be the first one at top with the node Id of 1 Z-Uno is the first and only easy to use developer board that allows you to create your own Z-Wave device without deep knowledge of Z-Wave protocol or programming. This is showing in the right hand top panel called "Node" AEON LABS Z-STICK (Z-Wave USB adapter) Product Overview: The Aeon Labs Z-Stick is a self-powered Z-Wave USB dongle with push button for remote network creation (independent from external power and host microprocessor). You should then see all info about this Aeon Z-Stick showing on the interfaceĪnd we no need to put the Z-Stick in to learn mode
#AEON LABS Z STICK II SERIAL#
It should show some thing like "USB Serial Device (ComXX): ControllerStaticLib"
#AEON LABS Z STICK II SOFTWARE#
You can get the Zenys tool software from here: (Its actual a tool by Sigma Alliance now as they purchased Zenys)ģ) Plug you Aeon Z-Stick in to a USB on you PCĤ) Select Categories -> Settings, Then select Detect This topic is about how to add a Aeon Labs Z-Stick as a second controller to this existing network.įirstly you going to need the Zensys tool to set up the z-stick in to learn mode to become a secondary controller. If it is not there you can find the official version here.If you have a Z-Wave network and it already has a controller, then you can add in a second controller if wish. You might find it in /boot/overlays/README on your SD-card. You should also check the README for details on the overlays. Exclusion will also reset your device and can sometimes help you with re-including it into your network. You should now be able to use Razberry Z-Wave from /dev/ttyAMA0.įor other operating systems such as Raspberry Pi OS you will also have to run the following command: sudo systemctl disable hciuart Aeon Labs Z-Stick Self-Powered Z-Wave USB adapter908.42mhz radio transceiver (Z-Wave technology) - Firmware upgradeable - USB specification 2. Learn how to exclude a device using your z-stick. Raspberry Pi 3 procedureįor Home Assistant OS this should be everything you need to do. Then shutdown, add the hat back, and boot again. Advanced functions include automatic rediscovery of the Z-Wave network and becoming a secondary or inclusion controller to a SIS gateway in the Z-Wave network. Reboot your Pi 4 without the Razberry Z-Wave hat first. Aeon Labs Minimote (Z-Wave Remote Controller) Introduction: The Minimote is a fully functional Z-Wave remote control capable of adding, removing and controlling other Z-Wave devices. Raspberry Pi 4 procedureĪdd the following parameters to the bottom of the /boot/config.txt file. You do this by adding the following to the end of /boot/config.txt:įor both processes below you will need to insert your SD card into your PC and open the /boot/config.txt file with your favorite text editor.
#AEON LABS Z STICK II BLUETOOTH#
You need to disable the on-board Bluetooth since the board requires the use of the hardware UART (and there’s only one on the Pi3). It’s totally normal for your Z-Wave stick to cycle through its LEDs (Yellow, Blue and Red) while plugged into your system. Both hardware revisions are still being sold, make informed purchasing decisions if using paired with a Pi 4. Aeotec has released a 2020 hardware revision ZW090-A/B/C Gen5+ with Pi 4 compatibility. There are known compatibility issues with older hardware versions of the Aeotec stick not working on the Raspberry Pi 4.
0 kommentar(er)
